SRB100DR

Descriere

Safety relay module for double reset
Suitable for signal processing of potential-free outputs, e.g. command devices
1 safety contact, STOP 0

Caracteristici

Ambient temperature, maximum	60
Ambient temperature, minimum	-25
Basic quantity unit	Piece
Cable section, maximum	2.5 mm²
Cable section, minimum	0.25 mm²
Climatic stress	EN 60068-2-78
Conduction resistance, maximum	40
Contact resistance, maximum	0.1
Current, Utilisation category AC-15	6
Current, Utilisation category DC13	6
Degree of pollution to IEC/EN 60664-1	2
Drop-out delay in case of emergency, typically	20
Drop-out delay in case of power failure, typically	80
EAN ( European Article Number)	4250116202218
EAN (European Article Number)	4250116202218
EMC rating	EMC-Directive
EPLAN	Yes
Earth connection detection	Yes
Electrical power consumption	3.2
Electronic Fuse	Yes
Enclosure material	Glass-fibre reinforced thermoplastic, ventilated
Frequency range	50; 60
Gross weight	250.000
Height	100
Indicated operating states	Position relay K2; Position relay K1; Position relay K3
Integral System Diagnostics, status	Yes
Material of the contacts, electrical	Ag-Ni, self-cleaning, positive drive
Mechanical life, minimum	10000000
Mission Time	20
Mounting	Snaps onto standard DIN rail to EN 60715
Net weight	250.000
Note (Contact resistance)	in new state
Note (General)	Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.
Note (Wiring diagram)	The wiring diagram is shown with guard doors closed and in de-energised condition.; Applications: #Picture#Bilddata/Sonstige/_quitz01.eps#/Picture# safety relay module for double reset; Start configuration: 2 time-dependent reset/on switches 1st and 2nd monitoring time between the 1st and 2nd reset button from 3 … 30 seconds adjustable through DIP switches; The monitoring time is set through DIP switches located below the cover of the enclosure front. (Factory setting: 3 seconds); Actuator configuration: 1-channel control (output impulse approx. 200 ms) of the reset input of a downstream safety relay module; Edge detection: After the device is reset, the trailing edge is evaluated, so that errors, e.g. welded contacts or manipulations cannot lead to dangerous situations.; (H2) = Feedback circuit
Number of LEDs	4
Number of openers	2
Number of safety contacts	1
Overvoltage category	III
PFH-Value Stop 0	0.00000002
Product group	Initial
Product name	SRB100DR
Product type description	SRB100DR
Protection class of Clips or Terminals	IP20
Protection class of the Clearance	IP54
Protection class of the enclosure	IP40
Pull-in delay at RESET, typically	20
Pull-in delay at automatic start, maximum, typically	100
Rated AC voltage for controls at DC minimum	20.4
Rated AC voltage for controls, 50 Hz, minimum	20.4
Rated AC voltage for controls, 60 Hz, minimum	20.4
Rated control voltage at AC 50 Hz, maximum	26.4
Rated control voltage at AC 60 Hz, maximum	26.4
Rated control voltage at DC, maximum	28.8
Rated impulse withstand voltage	4
Rated operating voltage	24 VAC -15% / +10%; 24 VDC -15% / +20%, residual ripple max. 10 %
Reset after disconnection of supply voltage	Yes
Resistance to vibrations to EN 60068-2-6	10...55 Hz, Amplitude 0.35 mm, ± 15 %
Restistance to shock	30 g / 11 ms
Standards	IEC 61508; EN 60947-5-1
Start input	Yes
Storage and transport temperature, maximum	85
Storage and transport temperature, minimum	-40
Switching capacity, maximum	250
Switching capacity, minimum	10
Terminal Connector	Screw connection; rigid or flexible
Terminal designations	IEC/EN 60947-1
Tightening torque of Clips	0.6
Voltage, Utilisation category AC15	230
Voltage, Utilisation category DC13	24
Width	22.5
Wire breakage detection	Yes
eCl@ss number, Version 9.0	27-37-18-19