SRB101EXi-1R

Caracteristici

Ambient temperature, maximum	60
Ambient temperature, minimum	-25
Automatic reset function	Yes
Basic quantity unit	Piece
Cable section, maximum	2.5 mm²
Cable section, minimum	0.25 mm²
Category, Stop 0	4
Certificates	ATEX; IECEX; IMMETRO
Climatic stress	EN 60068-2-78
Conduction resistance, maximum	30
Contact resistance, maximum	0.1
Degree of pollution to IEC/EN 60664-1	2
Diagnostic Coverage (DC) Level, Stop 0	≥ 99
Drop-out delay in case of "emergency stop", maximum	20
Drop-out delay in case of power failure, typically	20
EAN ( European Article Number)	4250116202355
EAN (European Article Number)	4250116202355
Earth connection detection	Yes
Electrical power consumption	3
Enclosure material	Glass-fibre reinforced thermoplastic, ventilated
Explosion protection category	2G; 2D
Explosion protection designation	<span class="symbol">D</span> II (2) G [Ex ib Gb] IIC; <span class="symbol">D</span> II (2) D [Ex ib Db] IIIC; <span class="symbol">D</span> II 3 G Ex nA nC IIC T5 Gc (Installation SRB, in Zone 2)
Explosion protection zones	1; 21
Explosion protection: regulations	EN 60079-0; EN 60079-15; EN 60079-11
Feedback circuit	Yes
Gross weight	220.000
Height	100
Integral System Diagnostics, status	Yes
Material of the contacts, electrical	AgSn0. self-cleaning, positive drive
Mechanical life, minimum	10000000
Mounting	Snaps onto standard DIN rail to EN 60715
Net weight	220.000
Note (Contact resistance)	in new state
Note (General)	Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.
Note (Wiring diagram)	The wiring diagram is shown with guard doors closed and in de-energised condition.; Monitoring 1 guard door(s), each with a magnetic safety sensor of the BNS range; If only one external relay or contactor is used to switch the load, the system can be classified in Control Category 3 to ISO 13849-1, if exclusion of the fault “Failure of the external contactor” can be substantiated and is documented, e.g. by using a reliable down-rated contactor. A second contactor leads to an increase in the level of security by redundant switching to switch the load off.; To secure a guard door up to PL e and Category 4; The feedback circuit monitors the position of the contactors KA and KB.; Automatic start: The automatic start is programmed by connecting the feedback circuit to the terminals X1/X2. If the feedback circuit is not required, establish a bridge.
Note (applications)	Safety sensor; Guard system; Emergency-Stop button; Pull-wire emergency stop switches
Number of LEDs	5
Number of auxiliary contacts	1
Number of openers	2
Number of safety contacts	1
Operating Current	57
Overvoltage category to IEC/EN 60664-1	3
PFH-Value Stop 0	0.00000002
Performance Level, Stop 0	e
Product group	Initial
Product name	SRB101EXI
Product type description	SRB101EXI-1R
Protection class of Clips or Terminals	IP20
Protection class of the Clearance	IP54
Protection class of the enclosure	IP40
Pull-in delay at RESET, typically	20
Pull-in delay at automatic start, maximum, typically	300
Rated AC voltage for controls at DC minimum	20.4
Rated control voltage at DC, maximum	28.8
Rated impulse withstand voltage	4
Rated operating voltage	24 VDC -15%/+20%, residual ripple max. 10%
Reset edge detection	Yes
Resistance to vibrations to EN 60068-2-6	10 ... 55 Hz, Amplitude 0.35 mm
Restistance to shock	30 g / 11 ms
Safety Integrity Level (SIL), Stop 0	3
Short-circuit recognition	Yes
Standards	IEC 61508; ISO 13849-1; EN 60947-5-1
Start input	Yes
Storage and transport temperature, maximum	85
Storage and transport temperature, minimum	-40
Terminal Connector	Screw connection; rigid or flexible
Terminal designations	IEC/EN 60947-1
Tightening torque of Clips	0.6
Utilisation category	DC-13; AC-15
Utilisation category AC-15	230
Utilisation category DC-13	24
Width	22.5
Wire breakage detection	Yes
eCl@ss number, Version 9.0	27-37-18-19