| AS-i Device protection | Internal short-circuit proof |
|---|---|
| AS-i Input, Channel 1 | Data bits DI 0 / DI 1 = dynamic code transmission |
| AS-i Input, Channel 2 | Data bits DI 2 / DI 3 = dynamic code transmission |
| AS-i Operating voltage AS-i maximum | 31.6 |
| AS-i Operating voltage, minimum | 18 |
| AS-i Outputs, DO 0 … DO 3 | No Function |
| AS-i Parameter bits, P0 | Channel 2 switched |
| AS-i Parameter bits, P1 | No function |
| AS-i Parameter bits, P2 | No function |
| AS-i Parameter bits, P3 | No function |
| AS-i Profile | S-0.B.F.F |
| AS-i Version | V 3.0 |
| AS-i, ID-Code | 0xB |
| AS-i, ID-Code1 | 0xF |
| AS-i, ID-Code2 | 0xF |
| AS-i, IO-Code | 0x0 |
| Actuating force, maximum | 200 |
| Actuating travel | 400 |
| Ambient temperature, maximum | 60 |
| Ambient temperature, minimum | -25 |
| Available until | 2020-12-31T00:00:00 |
| Basic quantity unit | Piece |
| Certificates | cULus; EAC; ASi-SaW |
| Control category to EN13849 | 4 |
| Degree of pollution to VDE 0100 | 3 |
| EAN ( European Article Number) | 4030661404455 |
| EAN (European Article Number) | 4030661404455 |
| Enclosure material | Plastic, glass-fibre reinforced thermoplastic, self-extinguishing |
| Gross weight | 230.000 |
| Height of sensor | 182.5 |
| Length of sensor | 51 |
| Length of the wire, maximum | 10 |
| Material of the cover | Plastic, glass-fibre reinforced thermoplastic, self-extinguishing |
| Mechanical life, minimum | 100000 |
| Mission Time | 20 |
| Net weight | 230.000 |
| Note (AS-i Parameter bits) | Set the parameter outputs to "1111" (0xF) ; FID: periphery error |
| Note (AS-i Input module address) | Preset to address 0, can be changed through AS-interface bus master or hand-held programming device |
| Note (AS-i Operating voltage) | Protection against polarity reversal |
| Note (Delivery capacity) | Phased-out product |
| Note (General) | Recommended cable lengths for pull-wire Emergency-Stop switches in relation to the range of ambient temperature.; As the thimbles are subject to deformation in case of wire pull, the wire should be pulled several times after fitting. After that, the wire must be re-tensioned using the eyebolt or the tensioner.; The addressing must take place via the M12 connector or the flat cable connection.; At 2 mm to 5 mm distance, intermediate wire supports are required, see accessories |
| Note (PFH-value) | up to max. 5,000 switching cycles/year |
| Note (Relative humidity) | non-condensing; non-icing |
| Operating Current | 50 |
| Overvoltage category | III |
| Overvoltage category to VDE 0100 | 3 |
| PFH-value | 0.000000014 |
| PIN 1 | AS-Interface + |
| PIN 2 | n.c. |
| PIN 3 | AS-Interface - |
| PIN 4 | n.c. |
| Performance level, up to | e |
| Product group | Initial |
| Product name | ZQ 700 AS |
| Product type description | ZQ 700 ST-AS |
| Protection class (Operating resource) | 2 |
| Protection rating | II |
| Rated impulse withstand voltage | 0.8 |
| Rated insulation voltage | 32 V |
| Reaction time, maximum | 100 |
| Relative humidity, maximum | 95 |
| Relative humidity, minimum | 30 |
| Resistance to vibrations to EN 60068-2-6 | 10 … 150 Hz, amplitude 0.35 mm / 5 g |
| Restistance to shock | 15 g / 11 ms |
| Safety Integrity Level (SIL), applicable for | 3 |
| Standards | IEC 61508 |
| Storage and transport temperature, maximum | 85 |
| Storage and transport temperature, minimum | -25 |
| Switching principle | Snap switch element |
| Terminal Connector | Connector plug M12, 4-pole, (A-coding) |
| Width of sensor | 40.5 |
| eCl@ss number, Version 9.0 | 27-37-12-01 |
| switching frequency | 3600 |
|---|
| protection class | IP67 to IEC 60529 |
|---|
Documentația poate fi solicitată împreună cu produsul.
Desenele pot fi solicitate împreună cu produsul.
