| Ambient temperature, maximum | 60 |
|---|---|
| Ambient temperature, minimum | -25 |
| Automatic reset function | Yes |
| Basic quantity unit | Piece |
| Cable section, maximum | 2.5 mm² |
| Cable section, minimum | 0.25 mm² |
| Category, Stop 0 | 4 |
| Certificates | CCC; cULus; TÜV; EAC; TILVA |
| Climatic stress | EN 60068-2-78 |
| Common Cause Failure (CCF), minimum | 65 |
| Conduction resistance, maximum | 40 |
| Contact resistance, maximum | 0.1 |
| Current, Utilisation category AC-15 | 6 |
| Current, Utilisation category DC13 | 6 |
| Degree of pollution to IEC/EN 60664-1 | 2 |
| Diagnostic Coverage (DC) Level, Stop 0 | ≥ 99 |
| Drop-out delay in case of emergency, typically | 20 |
| Drop-out delay in case of power failure, typically | 80 |
| EAN ( European Article Number) | 4030661476179 |
| EAN (European Article Number) | 4030661521589 |
| EMC rating | EMC-Directive |
| Earth connection detection | Yes |
| Electrical power consumption | 2 |
| Electronic Fuse | Yes |
| Enclosure material | Glass-fibre reinforced thermoplastic, ventilated |
| Feedback circuit | Yes |
| Frequency range | 50; 60 |
| Gross weight | 250.000 |
| Height | 120 |
| Indicated operating states | Position relay K2; Position relay K1; Internal operating voltage U<sub>i</sub> |
| Integral System Diagnostics, status | Yes |
| Material of the contacts, electrical | AgSn0. self-cleaning, positive drive |
| Mechanical life, minimum | 10000000 |
| Mission Time | 20 |
| Mounting | Snaps onto standard DIN rail to EN 60715 |
| Net weight | 250.000 |
| Note (Contact resistance) | in new state |
| Note (General) | Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit. |
| Note (LED switching conditions display) | QS: cross-wire short detection status (LED on when cross-wire short detection active). |
| Note (Wiring diagram) | The wiring diagram is shown with guard doors closed and in de-energised condition.; Input level: The example shows a 2-channel control of a guard door monitoring with two position switches, whereof one with positive break, external reset button (R) and feedback circuit (H2).; Relay outputs: Suitable for 2 channel control, for increase in capacity or number of contacts by means of contactors or relays with positive-guided contacts.; The control recognises cross-short, cable break and earth leakages in the monitoring circuit.; Switch setting: The cross-wire short detection function (factory default) is programmed by means of the switch located underneath the front cover of the module: Pposition nQS (top): no cross-wire short protection, suitable for 1-channel applications and applications with outputs with potential in the control circuits. Position QS (bottom): cross-wire short protection, suitable for 2-channel applications without outputs with potential in the control circuits.; For 1-channel control, connect NC contact to S11/S12 and bridge S12/S22 (QS-switch = nQS); Connect potential p-type outputs of safety light grids/curtains to S12/S22. The devices must have the same reference potential. QS-switch = nQS; Automatic start: The automatic start is programmed by connecting the feedback circuit to the terminals S12/X3. If the feedback circuit is not required, establish a bridge.; F1 = Hybrid fuse |
| Note (applications) | Safety sensor; Guard system; Emergency-Stop button; Pull-wire emergency stop switches; Safety light barriers |
| Number of LEDs | 5 |
| Number of auxiliary contacts | 1 |
| Number of openers | 2 |
| Number of safety contacts | 3 |
| Overvoltage category | III |
| PFH-Value Stop 0 | 0.00000002 |
| Performance level, stop 0, up to | e |
| Product group | Initial |
| Product name | SRB301ST |
| Product type description | SRB301ST-24V-(V.2) |
| Protection class of Clips or Terminals | IP20 |
| Protection class of the Clearance | IP54 |
| Protection class of the enclosure | IP40 |
| Pull-in delay at RESET, typically | 20 |
| Pull-in delay at automatic start, maximum, typically | 100 |
| Rated AC voltage for controls at DC minimum | 20.4 |
| Rated AC voltage for controls, 50 Hz, minimum | 20.4 |
| Rated AC voltage for controls, 60 Hz, minimum | 20.4 |
| Rated control voltage at AC 50 Hz, maximum | 26.4 |
| Rated control voltage at AC 60 Hz, maximum | 26.4 |
| Rated control voltage at DC, maximum | 28.8 |
| Rated impulse withstand voltage | 4 |
| Rated operating voltage | 24 VAC -15% / +10%; 24 VDC -15%/+20%, residual ripple max. 10% |
| Removable Terminals | Yes |
| Reset edge detection | Yes |
| Resistance to vibrations to EN 60068-2-6 | 10 ... 55 Hz, Amplitude 0.35 mm |
| Restistance to shock | 30 g / 11 ms |
| Safety Integrity Level (SIL), Stop 0, applicable for | 3 |
| Short-circuit recognition | Yes |
| Standards | IEC 61508; ISO 13849-1; EN 62061 |
| Start input | Yes |
| Storage and transport temperature, maximum | 85 |
| Storage and transport temperature, minimum | -40 |
| Switching capacity, maximum | 250 |
| Switching capacity, minimum | 10 |
| Terminal Connector | Screw connection, plug-in; rigid or flexible |
| Terminal designations | IEC/EN 60947-1 |
| Tightening torque of Clips | 0.6 |
| Voltage, Utilisation category AC15 | 230 |
| Voltage, Utilisation category DC13 | 24 |
| Width | 22.5 |
| Wire breakage detection | Yes |
| eCl@ss number, Version 9.0 | 27-37-18-19 |
| Weight | 240 |
|---|
| depth | 121 |
|---|
Documentația poate fi solicitată împreună cu produsul.
Desenele pot fi solicitate împreună cu produsul.
