SRB402NE 230V

Descriere

Fit for signal evaluation of outputs of safety magnetic switches (to this end, integrated current and voltage limiters)
Possibility to connect a non-contact end switch or speed reduction switch
2 safety contacts, switch-off level 1;
2 safety contacts, switch-off level 2
2 Signalling outputs

Caracteristici

Ambient temperature, maximum	45
Ambient temperature, minimum	-25
Automatic reset function	Yes
Basic quantity unit	Piece
Cable section, maximum	2.5 mm²
Cable section, minimum	0.25 mm²
Category, Stop 0	4
Certificates	EAC
Climatic stress	EN 60068-2-78
Common Cause Failure (CCF), minimum	65
Conduction resistance, maximum	40
Contact resistance, maximum	0.1
Current, Utilisation category AC-15	4
Current, Utilisation category DC13	4
Degree of pollution to IEC/EN 60664-1	2
Diagnostic Coverage (DC) Level, Stop 0	≥ 99
Drop-out delay in case of emergency, typically	20
Drop-out delay in case of power failure, typically	80
EAN ( European Article Number)	4250116202423
EAN (European Article Number)	4250116202423
EMC rating	EMC-Directive
Earth connection detection	Yes
Electrical power consumption	6
Enclosure material	Glass-fibre reinforced thermoplastic, ventilated
Feedback circuit	Yes
Frequency range	50; 60
Gross weight	550.000
Height	100
Indicated operating states	Position relay K2; Position relay K1; Internal operating voltage U<sub>i</sub>; Position relay K3; Position relay K5
Integral System Diagnostics, status	Yes
Material of the contacts, electrical	Ag-Ni, self-cleaning, positive drive
Mechanical life, minimum	10000000
Mission Time	20
Mounting	Snaps onto standard DIN rail to EN 60715
Net weight	550.000
Note (Contact resistance)	in new state
Note (General)	Inductive loads (e.g. contactors, relays, etc.) are to be suppressed by means of a suitable circuit.
Note (Wiring diagram)	The control system recognises wire-breakage and earth faults in the monitoring circuit.; The example shows a 1-channel control with contact A for a guard door monitor; of which at least one contact has positive break; with external reset button (R).; Relay outputs: Suitable for 1 channel control, for increase in capacity or number of contacts by means of contactors or relays with positive-guided contacts.; The wiring diagram is shown with non-actuated limit switches and in de-energised condition.; (H2) = Feedback circuit
Note (applications)	Safety sensor; Guard system
Number of LEDs	7
Number of auxiliary contacts	2
Number of openers	4
Number of safety contacts	4
Number of signalling outputs	2
Overvoltage category	III
PFH-value	0.00000002
Performance level, stop 0, up to	e
Product group	Initial
Product name	SRB402NE
Product type description	SRB402NE 230V
Protection class of Clips or Terminals	IP20
Protection class of the Clearance	IP54
Protection class of the enclosure	IP40
Pull-in delay at RESET, typically	20
Pull-in delay at automatic start, maximum, typically	100
Rated AC voltage for controls, 50 Hz, minimum	195.5
Rated AC voltage for controls, 60 Hz, minimum	195.5
Rated control voltage at AC 50 Hz, maximum	253
Rated control voltage at AC 60 Hz, maximum	253
Rated impulse withstand voltage	4
Rated operating voltage	230 VAC -15% / + 10%
Removable Terminals	Yes
Replacement article number	101178532
Resistance to vibrations to EN 60068-2-6	10...55 Hz, Amplitude 0.35 mm, ± 15 %
Restistance to shock	30 g / 11 ms
Safety Integrity Level (SIL), Stop 0, applicable for	3
Short-circuit recognition	Yes
Standards	IEC 61508; IEC/EN 60947-1
Storage and transport temperature, maximum	85
Storage and transport temperature, minimum	-40
Switching capacity, maximum	250
Switching capacity, minimum	10
Terminal Connector	Screw connection; rigid or flexible
Terminal designations	IEC/EN 60947-1
Tightening torque of Clips	0.6
Voltage, Utilisation category AC15	230
Voltage, Utilisation category DC13	24
Width	45
Wire breakage detection	Yes
eCl@ss number, Version 9.0	27-37-18-19